Ürün ayrıntıları:
Ödeme & teslimat koşulları:
|
Kontrol metodu: | PLC programlı kontrol | Test hızı: | 10 ± 3 mm / dak |
---|---|---|---|
güç: | 380v / 50Hz | Ürün adı: | mobilya test etme donanımları |
Sıkma hızı: | 5-50 mm'lik / dakika | Standart: | ASTM D6055 |
Vurgulamak: | mobilya test etme donanımları,Test makine etkiler |
Güvenlik Mobilya Test Cihazları, Büyük Ürünler Paket Kelepçe Kuvvet Test Cihazları
1. Before placing the packaged product between platens, verify that the clamp force using the clamp indicator. Paketlenmiş ürünü plakalar arasına yerleştirmeden önce, kelepçe göstergesini kullanarak kelepçe kuvvetinin doğrulandığından emin olun. The indicator should be placed between the axes of the platen articulation points approximately 1/2 way up the platens. Gösterge, merdanelerin artikülasyon noktalarının eksenleri arasında, merdanelerin yaklaşık 1/2 katı kadar yerleştirilmelidir.
2. Ürün her sıkıştırıldığında, kuvvet en az 15 saniye uygulanmalı ve 1 dakikayı geçmemelidir.
3. Apply the clamp force on the sample with the platens resting on the floor and the front edge of the platens flush with the front of the package (see flush platen photo 4). Merdaneler zemine ve merdanelerin ön kenarına paketin ön tarafı ile aynı hizada olacak şekilde numuneye kelepçe kuvveti uygulayın (bkz. Düz plaka fotoğraf 4). If the package is too large for the clamps to be flush to front edge (ie, large refrigerator, tractor etc.), clamp as close to the edge as possible. Paket, kelepçelerin ön kenara (yani büyük buzdolabı, traktör vb.) Hizalanması için çok büyükse, kenara mümkün olduğunca yakın kelepçeleyin.
4. Ürünü yıkama yönünde toplam 10 kez klempleyin.
5. Apply the clamp force on the packaged product with the platens in a 6×6 inch(15.2x15.2cm) offset position(see fig 5 ). Merdaneleri 6 x 6 inç (15,2x15,2 cm) ofset konumunda olacak şekilde paketlenmiş ürüne kelepçe kuvveti uygulayın (bkz. Şekil 5). Both the horizontal and vertical offset dimensions are measured at the front bottom corner of the platen. Hem yatay hem de dikey ofset boyutları, plakanın ön alt köşesinde ölçülür. If the package is too large for the clamp to be positioned 6-inches from the front edge (ie, large refrigerator, tractor etc.), clamp as close to this position as possible. Ambalaj, kelepçenin ön kenardan 6 inç (yani büyük buzdolabı, traktör vb.) İçin yerleştirilemeyecek kadar büyükse, bu konuma mümkün olduğunca yakın kelepçeleyin.
1) Exception number 1: for large products with an obvious, visible external skid(see fig 6), offset clamp testing is not conducted if the product does not extend beyond any part of the skid and there is some form of handling graphic or note that indicates to clamp only from the skid. 1) İstisna numarası 1: Açık, görünür bir dış kızağı olan büyük ürünler için (bkz. Şekil 6), ürün kızağın herhangi bir kısmının ötesine geçmiyorsa ve bir tür taşıma grafiği veya notu varsa ofset kelepçe testi yapılmaz. bu sadece kızaktan kelepçelendiğini gösterir. If there is no graphic or not indicating this or there is some overhang beyond the skid, then the entire clamp test protocol is conducted. Herhangi bir grafik yoksa veya bunu göstermiyorsa veya kızağın ötesinde bir çıkıntı varsa, tüm kelepçe test protokolü gerçekleştirilir.
2) İstisna numarası 2: Ürün yüksekliği, normal nakliye yönüne yerleştirildiğinde ≤ 12 inç ise, 6 x6 inç ofset testi yapılmaz.
6. 6 x6 inç ofset konumunda kelepçe ile ürünü toplam 10 kez klempleyin.
7. Repeat step 5.2.5 except with a 2 x6 inch offset clamp position. 2 x 6 inç ofset kelepçe konumu hariç 5.2.5 adımını tekrarlayın. The 2 x6 inch offset is similar to the 6 x6 inch offset except the platens are oriented such that they are 2-inches from the floor and 6-inches back from the package's front edge. 2 x6 inç ofset, 6 x6 inç ofsete benzer, ancak plakalar yerden 2 inç ve paketin ön kenarından 6 inç geri olacak şekilde yönlendirilir. If the package is too large for the clamps to be positioned 2-inches from the front edge (ie, large refrigerator, tractor etc.), clamp as close to this position as possible. Paket, kelepçelerin ön kenardan 2 inç (yani büyük buzdolabı, traktör vb.) İçin yerleştirilemeyecek kadar büyükse, bu konuma mümkün olduğunca yakın kelepçeleyin.
8. . Repeat flush and offset clamping on all other sides of the product that are indicated in the handling graphics as acceptable for clamp handling. Ürünün, elleçleme grafiklerinde kelepçe kullanımı için kabul edilebilir olduğu belirtilen tüm diğer taraflarında aynı hizada ve ofset kelepçeyi tekrarlayın.
Karar standartlarına göre, testte başarısız olan bir öğe varsa, “Test Hatası İşleme Sayfası
Güvenlik koruması
Aşırı yük koruması, aşırı gerilim koruması ve sınırlı konum koruma cihazı
Sıkma kuvveti: |
50-3000kg |
Sıkma kurulu boyutu: |
1200 x 1200mm |
Maksimum sıkıştırma alanı: |
1200 x 1200 x 1200 mm |
Minimum sıkıştırma alanı: |
400 x 1200 x 1200 mm |
Sıkıştırma hızı: |
5-50 mm'lik / dakika |
Yukarı-aşağı alan: |
100-600mm, ayarlanabilir, özelleştirilebilir |
Boyutlar: 3 |
810 - 1900 - 2100 |
Ağırlık: |
800 kg |
Güç: |
380v / 50Hz |
Kontrol sistemi: |
PLC programlı kontrol |
Özellikler
Paket kelepçe test makinesi
1. ASTM D6055'e kadar
2. PLC kontrolü
Parametreler
Sıkma kuvveti |
1T |
renk |
isteğe bağlı |
çözüm |
1 / 100,000 |
Test Alanı (U x G x Y) |
100x 100 x 100cm |
Hız testi |
10 ± 3 mm / dak |
Ağırlık |
yaklaşık 300kg |
Güç |
1 #, 220V / 50HZ |
İlgili kişi: Kelly